2 × Rapid Taq Master Mix P222 Gene Bio Systems

Q1: The amplification efficiency is low and there are no amplified bands in the test group.

A1: (1) Primers

Check whether the synthetic primers have degraded due to improper storage; review primer design and use BLAST to examine primer specificity or redesign primers.

(2) Template

Long-term storage or repeated freeze-thaw cycles will lead to DNA breakage, nicking, or degradation, so the template should be the freshly prepared double-stranded DNA. An excessively high GC content in the template will make it difficult to separate DNA double strands; in this case, add PCR Enhancer (Cat. No. P021) to effectively lower the melting temperature. Crude sample templates may contain inhibitors, so it is recommended to lower the template concentration (use after dilution; if a plant leaf is used, make sure the plant is not rich in polysaccharides or polyphenols, take a fresh, young leaf, and trim it to the size of the end of a yellow pipette tip). If cDNA is used, check the purity and integrity of the RNA used for reverse transcription.

(3) Enzyme

The enzyme used in the reaction has been inactivated. Repeat the experiment with a fresh enzyme or an enzyme from another source.

(4) Amplification system

The reaction system has been prepared incorrectly. Repeat the experiment with the correct system.

(5) Reaction program

Check whether the denaturation temperature is correct and whether the temperature displayed on the PCR system is the same as the actual temperature. If the temperature is too high, the enzyme will be rapidly inactivated in the first few cycles. If the temperature is too low, the template will not be completely denatured. If yeast is used as the template, the pre-denaturation time may be extended to 10 minutes. If the annealing temperature is inappropriate, determine the appropriate annealing temperature by testing a gradient of annealing temperatures. If the target fragment is long, try the touchdown PCR program. Check whether the extension time is sufficient.

 

Q2: The amplified bands are faint.

A2: (1) Primers

Check whether the synthetic primers have degraded.

(2) Template

Check the quality of the template. Long-term storage or repeated freeze-thaw cycles will lead to DNA breakage, nicking, or degradation, so the freshly prepared double-stranded DNA should be used as the template. If the template has been used up, use serial dilutions of the initial amplification product as the templates for subsequent amplification.

(3) Reaction program

Try the touchdown PCR program; increase the extension time and the number of cycles.

 

Q3: Amplification specificity is poor, or there are non-specific products.

A3: (1) Primers

Primer design is not optimal. If primers have bound to non-specific sites in the target sequence or to each other to form dimers, optimize by reducing the primer concentration or redesigning primers if necessary.

(2) Template

If the template is impure or contaminated, prepare a new template.

If the template has degraded, or too much template has been used, examine the integrity and concentration of the template by electrophoresis, and purify the template again if necessary. Consult the Instructions for Use for the template input amount.

(3) Reaction program

The reaction program is not optimal. If there are non-specific miscellaneous bands smaller than the target band, increase the annealing temperature and reduce the number of cycles. If there are non-specific miscellaneous bands larger than the target band, reduce the extension time and the number of cycles.

 

Q4: The bands are diffuse or smeared when amplification products are run on a gel.

A4: (1) Gel

Melt the gel completely during preparation.

(2) Primers

Check whether the primers have degraded.

(3) Template

The template is degraded or excessive. Examine the integrity and concentration of the template by electrophoresis, and prepare a new template if necessary. Consult the Instructions for Use for the template input amount. If the target band is long and the cDNA is used as the template, check the purity and integrity of the RNA used for reverse transcription, and perform reverse transcription again without random primers.

(4) Reaction program

The reaction program is not optimal. If the annealing temperature is inappropriate, determine the appropriate annealing temperature by testing a gradient of annealing temperatures. Try the touchdown PCR program.

 

Q5: There are amplification products in the blank control (NTC) group.

A5: (1) Problematic primer design

The amplified sequence is homologous to the non-target sequence. Thus, non-target sequences are also amplified in PCR.

(2) If the band corresponding to the amplification product has the same size as the target bands, this indicates contamination.

Repeat the experiment with a fresh Mix, water, or primers. Prepare the reaction system on an ultra-clean workbench to minimize aerosol contamination.

(3) To avoid cross-contamination of the target sequence by the genome or large fragments, perform the steps with care to prevent the target sequence from being pipetted into the loading pipette or spilling from centrifuge tubes.

(4) To avoid contamination of the target gene by small airborne nucleic acid fragments, use the nested PCR method to reduce or eliminate contamination.

 

Q6: Do dyed PCR products affect restriction digestion?

A6: Tests show that dyed PCR products do not affect restriction digestion.